Not affiliated with or endorsed by the FCC, NCVEC, ARRL or any VEC. Questions are the NCVEC pools word for word (public domain); explanations are our own. Exam rules and fees can change: check with your VE team.
E4E: Noise and interference: external RF interference; electrical and computer noise; line noise; DSP filtering and noise reduction; common-mode current; surge protectors; single point ground panel
Group E4E of the Amateur Extra pool (2024–2028) has 14 active questions. One of them is on every Amateur Extra exam. Each is shown word for word; open it to see the correct answer and our explanation.
E4E01
What problem can occur when using an automatic notch filter (ANF) to remove interfering carriers while receiving CW signals?
A Removal of the CW signal as well as the interfering carrier
B Any nearby signal passing through the DSP system will overwhelm the desired signal
C Excessive ringing
D All these choices are correct
Show the answer and explanation
Correct answer: A. Removal of the CW signal as well as the interfering carrier
Why A is right. A. A CW signal is itself a steady carrier, so an automatic notch filter may treat it as interference and remove it.
An automatic notch filter (ANF) uses DSP to find steady tones and cut them out. That works well on a whistle interfering with voice. A Morse signal is also a steady tone while the key is down, so the ANF cannot tell it from the unwanted carrier. For CW, turn the ANF off and use a narrow filter.
Why not B? The ANF reduces steady tones; it does not make nearby signals overwhelm the one you want.
E4E02
Which of the following types of noise can often be reduced by a digital noise reduction?
A Broadband white noise
B Ignition noise
C Power line noise
D All these choices are correct
Show the answer and explanation
Correct answer: D. All these choices are correct
Why D is right. D. Digital noise reduction can often reduce all three kinds, so every choice is correct.
DSP noise reduction looks for patterns. Speech and Morse have structure that changes in a predictable way, while noise is random or repeats differently. The processor keeps what looks like signal and suppresses the rest, whether it is steady hiss (white noise), engine ignition pulses or buzz from power lines.
E4E03
Which of the following types of noise are removed by a noise blanker?
A Broadband white noise
B Impulse noise
C Hum and buzz
D All these choices are correct
Show the answer and explanation
Correct answer: B. Impulse noise
Why B is right. B. A noise blanker detects short, sharp pulses and briefly mutes the receiver during each one, which removes impulse noise.
Impulse noise comes from sparks, such as car ignitions or electric fences. Each pulse is very short but strong. The blanker spots it and shuts the receive path for a few millionths of a second. Steady noise has no separate pulses, so a blanker cannot help with hiss or hum.
Why not A? Broadband white noise is continuous, so there are no separate pulses to cut out.
E4E04
How can conducted noise from an automobile battery charging system be suppressed?
A By installing filter capacitors in series with the alternator leads
B By installing a noise suppression resistor and a blocking capacitor at the battery
C By installing a high-pass filter in series with the radio’s power lead and a low-pass filter in parallel with the antenna feed line
D By installing ferrite chokes on the charging system leads
Show the answer and explanation
Correct answer: D. By installing ferrite chokes on the charging system leads
Why D is right. D. Ferrite chokes on the charging leads block RF noise from the alternator while passing the DC charging current.
An alternator and its regulator switch current rapidly, creating RF noise that travels along the wiring. A ferrite choke adds impedance (opposition to current) at radio frequencies but almost none to DC. Ferrites on the leads keep the noise from spreading through the vehicle wiring to your radio.
Why not A? A capacitor in series with the alternator lead would block DC and stop charging.
E4E05
What is used to suppress radio frequency interference from a line-driven AC motor?
A A high-pass filter in series with the motor’s power leads
B A brute-force AC-line filter in series with the motor’s power leads
C A bypass capacitor in series with the motor’s field winding
D A bypass choke in parallel with the motor’s field winding
Show the answer and explanation
Correct answer: B. A brute-force AC-line filter in series with the motor’s power leads
Why B is right. B. A brute-force AC-line filter in series with the motor leads blocks the motor's RF noise while passing the 60 Hz power.
Brushes and switches in a motor make sparks that put RF noise on the power wiring, which then radiates. A brute-force filter is a low-pass filter of series coils and capacitors to ground, built to carry full line current. It passes 60 Hz power and blocks the much higher radio frequencies.
Why not A? A high-pass filter would block the 60 Hz power and pass the noise.
E4E06
What type of electrical interference can be caused by computer network equipment?
A A loud AC hum in the audio output of your station’s receiver
B A clicking noise at intervals of a few seconds
C The appearance of unstable modulated or unmodulated signals at specific frequencies
D A whining-type noise that continually pulses off and on
Show the answer and explanation
Correct answer: C. The appearance of unstable modulated or unmodulated signals at specific frequencies
Why C is right. C. Network gear runs on clocks and data signals that leak out as steady or modulated carriers on fixed frequencies.
Routers, switches and network cables carry fast digital signals. Their clock frequencies and harmonics escape as signals at specific spots on the dial. Some are steady carriers; others warble or shift with data traffic, so they may come and go as network use changes.
Why not A? A loud AC hum points to 60 Hz power problems, not digital circuits.
E4E07
Which of the following can cause shielded cables to radiate or receive interference?
A Low inductance ground connections at both ends of the shield
B Common-mode currents on the shield and conductors
C Use of braided shielding material
D Tying all ground connections to a common point resulting in differential-mode currents in the shield
Show the answer and explanation
Correct answer: B. Common-mode currents on the shield and conductors
Why B is right. B. Common-mode current flows the same way on the outside of the shield and on the conductors, so the cable acts like an antenna.
In a working cable, currents on the inner conductors and the inside of the shield are equal and opposite, so their fields cancel. Common-mode current flows the same direction on everything, usually on the shield's outer surface. Its fields do not cancel, so the cable radiates and also picks up outside signals.
Why not A? Low-inductance grounds at both ends help the shield work; they do not cause leakage.
E4E08
What current flows equally on all conductors of an unshielded multiconductor cable?
A Differential-mode current
B Common-mode current
C Reactive current only
D Magnetically-coupled current only
Show the answer and explanation
Correct answer: B. Common-mode current
Why B is right. B. Common-mode current is the part that flows in the same direction and amount on every conductor at once.
Differential-mode current goes out on one wire and back on another; that is the useful signal. Common-mode current travels on all wires together and returns through some other path, such as ground. Because it does not cancel, it is a main cause of radiated interference. A ferrite choke around the whole cable reduces it.
Why not A? Differential-mode current flows in opposite directions on two conductors.
E4E09
What undesirable effect can occur when using a noise blanker?
A Received audio in the speech range might have an echo effect
B The audio frequency bandwidth of the received signal might be compressed
C Strong signals may be distorted and appear to cause spurious emissions
D FM signals can no longer be demodulated
Show the answer and explanation
Correct answer: C. Strong signals may be distorted and appear to cause spurious emissions
Why C is right. C. Strong signals can trigger the blanker, which chops them, distorts them and makes them seem to have spurious emissions.
A noise blanker mutes the receiver whenever it sees a sharp pulse. Strong signals with fast changes, such as loud SSB or CW, can look like pulses to it. The rapid on-off muting distorts them and spreads energy to nearby frequencies, so clean stations appear to be splattering.
Why not D? A blanker acts on short pulses; it does not stop FM from being demodulated.
E4E10
Which of the following can create intermittent loud roaring or buzzing AC line interference?
A Arcing contacts in a thermostatically controlled device
B A defective doorbell or doorbell transformer inside a nearby residence
C A malfunctioning illuminated advertising display
D All these choices are correct
Show the answer and explanation
Correct answer: D. All these choices are correct
Why D is right. D. All three can arc or buzz on the power line, so every choice is correct.
Line noise usually comes from an electrical arc, a small spark jumping a gap. Thermostat contacts in heaters and appliances can arc as they open and close. A failing doorbell transformer can buzz and arc. Lighted signs with bad transformers do the same. The noise starts and stops with the faulty device.
E4E11
What could be the cause of local AM broadcast band signals combining to generate spurious signals on the MF or HF bands?
A One or more of the broadcast stations is transmitting an over-modulated signal
B Nearby corroded metal connections are mixing and reradiating the broadcast signals
C You are receiving skywave signals from a distant station
D Your station receiver IF amplifier stage is overloaded
Show the answer and explanation
Correct answer: B. Nearby corroded metal connections are mixing and reradiating the broadcast signals
Why B is right. B. Corroded metal joints act like crude diodes, mixing strong broadcast signals and reradiating the products on new frequencies.
A rusty joint in a fence, gutter or tower can conduct better one way than the other, which makes it nonlinear. Strong AM signals induced in the metal mix at that joint and create sums, differences and harmonics. The metal then radiates them, so they reach your antenna like real signals.
Why not A? Overmodulation splatters near the station's own frequency, not onto other MF or HF bands.
E4E12
What causes interference received as a series of carriers at regular intervals across a wide frequency range?
A Switch-mode power supplies
B Radar transmitters
C Wireless security camera transmitters
D Electric fences
Show the answer and explanation
Correct answer: A. Switch-mode power supplies
Why A is right. A. A switch-mode power supply switches at a fixed rate, and the harmonics of that rate make carriers at regular steps across a wide range.
Switching supplies turn current on and off tens or hundreds of thousands of times per second. The sharp edges create harmonics at every multiple of the switching frequency. On the band you hear evenly spaced carriers, which may drift as the load changes.
Why not D? Electric fences make clicks or pops about once a second, not steady carriers.
E4E13
Where should a station AC surge protector be installed?
A At the AC service panel
B At an AC outlet
C On the single point ground panel
D On a ground rod outside the station
Show the answer and explanation
Correct answer: C. On the single point ground panel
Why C is right. C. Putting the surge protector on the single point ground panel bonds it to the same ground as every other protector in the station.
The single point ground panel is where every cable entering the station connects to one ground system. Installing the AC protector there means the AC, antenna and control lines share one ground reference. A surge then raises everything together instead of creating a voltage difference between pieces of equipment.
Why not A? At the service panel, the protector's ground would be separate from the station's other protectors, allowing voltage differences between them.
E4E14
What is the purpose of a single point ground panel?
A Remove AC power in case of a short-circuit
B Prevent common-mode transients in multi-wire systems
C Eliminate air gaps between protected and non-protected circuits
D Ensure all lightning protectors activate at the same time
Show the answer and explanation
Correct answer: D. Ensure all lightning protectors activate at the same time
Why D is right. D. Bonding all lightning protectors to one panel gives them the same ground, so they respond to a surge together.
If protectors sit on different grounds, one may fire before another, and the voltage difference can drive current through your equipment. With every coax, rotator and power protector on one plate tied to one ground system, they all see the surge at the same moment, and everything rises and falls together.
Why not A? Breakers and fuses handle short circuits; that is not the panel's job.