Not affiliated with or endorsed by the FCC, NCVEC, ARRL or any VEC. Questions are the NCVEC pools word for word (public domain); explanations are our own. Exam rules and fees can change: check with your VE team.
E7C: Filters and matching networks: types of networks; types of filters; filter applications; filter characteristics; impedance matching
Group E7C of the Amateur Extra pool (2024–2028) has 11 active questions. One of them is on every Amateur Extra exam. Each is shown word for word; open it to see the correct answer and our explanation.
E7C01
How are the capacitors and inductors of a low-pass filter Pi-network arranged between the network’s input and output?
A Two inductors are in series between the input and output, and a capacitor is connected between the two inductors and ground
B Two capacitors are in series between the input and output, and an inductor is connected between the two capacitors and ground
C An inductor is connected between the input and ground, another inductor is connected between the output and ground, and a capacitor is connected between the input and output
D A capacitor is connected between the input and ground, another capacitor is connected between the output and ground, and an inductor is connected between the input and output
Show the answer and explanation
Correct answer: D. A capacitor is connected between the input and ground, another capacitor is connected between the output and ground, and an inductor is connected between the input and output
Why D is right. D. Capacitors to ground at both ends shunt high frequencies away, while the series inductor between them blocks highs, so only low frequencies pass.
A capacitor's reactance falls as frequency rises, so a capacitor to ground shorts high frequencies. An inductor's reactance rises with frequency, so a coil in the signal path blocks them. Drawn out, the coil is the top bar of the Greek letter pi and the two capacitors are its legs.
Why not B? Series capacitors with an inductor to ground block low frequencies, which makes a high-pass network.
E7C02
What is the frequency response of a T-network with series capacitors and a shunt inductor?
A Low-pass
B High-pass
C Band-pass
D Notch
Show the answer and explanation
Correct answer: B. High-pass
Why B is right. B. Series capacitors block low frequencies and the shunt inductor drains them to ground, so only high frequencies get through.
Capacitors pass high frequencies easily and resist low ones. An inductor to ground has low reactance at low frequencies, shorting them out, but high reactance at high frequencies, leaving them alone. Both parts favor the highs.
Why not A? A low-pass network would need series inductors and a capacitor to ground, the reverse arrangement.
E7C03
What is the purpose of adding an inductor to a Pi-network to create a Pi-L-network?
A Greater harmonic suppression
B Higher efficiency
C To eliminate one capacitor
D Greater transformation range
Show the answer and explanation
Correct answer: A. Greater harmonic suppression
Why A is right. A. The added series inductor gives one more low-pass section, so harmonics above the operating frequency are cut more sharply.
In a low-pass ladder, each added reactive part makes the response fall faster above cutoff. A pi network has three parts; adding a series coil after the output capacitor makes four. The steeper slope weakens harmonics, the whole-number multiples of the operating frequency, before they reach the antenna.
Why not C? A Pi-L network adds a part; it does not remove a capacitor.
E7C04
How does an impedance-matching circuit transform a complex impedance to a resistive impedance?
A It introduces negative resistance to cancel the resistive part of impedance
B It introduces transconductance to cancel the reactive part of impedance
C It cancels the reactive part of the impedance and changes the resistive part to the desired value
D Reactive currents are dissipated in matched resistances
Show the answer and explanation
Correct answer: C. It cancels the reactive part of the impedance and changes the resistive part to the desired value
Why C is right. C. A matching network adds opposite reactance to cancel the load's reactance and transforms the remaining resistance to the value the source needs.
A complex impedance has a resistive part, which absorbs power, and a reactive part, which stores and returns it. The network supplies an equal and opposite reactance so the two cancel. Its coils and capacitors also step the resistance up or down, like a transformer, until it equals, for example, 50 ohms.
Why not D? An ideal matching network uses lossless coils and capacitors, so it dissipates nothing.
E7C05
Which filter type has ripple in the passband and a sharp cutoff?
A A Butterworth filter
B An active LC filter
C A passive op-amp filter
D A Chebyshev filter
Show the answer and explanation
Correct answer: D. A Chebyshev filter
Why D is right. D. A Chebyshev design accepts some ripple in the passband in exchange for a steeper drop past the cutoff.
Filter designs trade flatness against sharpness. A Chebyshev filter lets its passband response wiggle up and down by a set amount, called ripple. In return its sides fall off faster than a Butterworth filter with the same number of parts, which has a flat passband but a gentler cutoff.
Why not A? A Butterworth filter has the flattest passband, with no ripple.
E7C06
What are the characteristics of an elliptical filter?
A Gradual passband rolloff with minimal stop-band ripple
B Extremely flat response over its pass band with gradually rounded stop-band corners
C Extremely sharp cutoff with one or more notches in the stop band
D Gradual passband rolloff with extreme stop-band ripple
Show the answer and explanation
Correct answer: C. Extremely sharp cutoff with one or more notches in the stop band
Why C is right. C. An elliptical filter puts notches right beside its passband, giving the steepest change from pass to stop among common designs.
Elliptical, or Cauer, filters allow ripple in both the passband and the stopband. In exchange they place notches, frequencies where the response drops nearly to zero, right next to the cutoff. That makes the edge very sharp for a given number of parts.
Why not B? A flat passband with gently rounded corners describes a Butterworth filter.
E7C07
Which describes a Pi-L network?
A A Phase Inverter Load network
B A Pi-network with an additional output series inductor
C A network with only three discrete parts
D A matching network in which all components are isolated from ground
Show the answer and explanation
Correct answer: B. A Pi-network with an additional output series inductor
Why B is right. B. The name describes the shape: a pi section of capacitor, coil and capacitor, then an L made by one more series coil at the output.
The pi part is a capacitor to ground, a series coil and another capacitor to ground; it does the main impedance matching in many tube amplifiers. The extra series coil, the L, adds filtering. Together they use four parts, two of them connected to ground.
Why not A? Pi-L names the shape of the circuit, a pi followed by an L, not a phase inverter.
E7C08
Which of the following is most frequently used as a band-pass or notch filter in VHF and UHF transceivers?
A A Sallen-Key filter
B A helical filter
C A swinging choke filter
D A finite impulse response filter
Show the answer and explanation
Correct answer: B. A helical filter
Why B is right. B. A helical filter, a wire coil inside a metal can, gives sharp, low-loss resonance in a small space at VHF and UHF.
At VHF and UHF, ordinary coils and capacitors get lossy and tiny values are hard to control. A helical resonator is a wire spiral inside a shielded can that acts like a compact resonant line. Several coupled cans make a selective band-pass or notch filter for a radio's front end.
Why not D? A finite impulse response filter is a digital filter that works on samples, not on the RF signal in the front end.
E7C09
What is a crystal lattice filter?
A A power supply filter made with interlaced quartz crystals
B An audio filter made with four quartz crystals that resonate at 1 kHz intervals
C A filter using lattice-shaped quartz crystals for high-Q performance
D A filter for low-level signals made using quartz crystals
Show the answer and explanation
Correct answer: D. A filter for low-level signals made using quartz crystals
Why D is right. D. A crystal lattice filter combines several quartz crystals into a very narrow, steep filter for low-level signals, such as in a receiver's IF stage.
Quartz crystals resonate very sharply with very little loss. Arranging several, cut to slightly different frequencies, gives a flat-topped passband with steep sides. Receivers use these filters to select a single SSB or CW signal. They handle small signal levels, not power supply currents.
Why not C? The name comes from how the crystals are wired together, not from the shape of the crystals.
E7C10
Which of the following filters is used in a 2-meter band repeater duplexer?
A A crystal filter
B A cavity filter
C A DSP filter
D An L-C filter
Show the answer and explanation
Correct answer: B. A cavity filter
Why B is right. B. A duplexer must keep a strong transmitter out of a receiver only 600 kHz away, which takes the very sharp, low-loss response of cavity filters.
A repeater transmits and receives at the same time on one antenna. The duplexer separates the two frequencies. Cavity filters are metal tubes with a tuned rod inside, resonant like a quarter-wave line, and they handle full transmitter power with little loss. Several in a row give the deep isolation needed.
Why not A? Crystal filters are for low signal levels and cannot handle transmitter power.
E7C11
Which of the following measures a filter’s ability to reject signals in adjacent channels?
A Passband ripple
B Phase response
C Shape factor
D Noise factor
Show the answer and explanation
Correct answer: C. Shape factor
Why C is right. C. Shape factor compares a filter's bandwidth far down its sides with its bandwidth near the top, which shows how well it rejects nearby signals.
A common shape factor is the 60 dB bandwidth divided by the 6 dB bandwidth. A value near 1 means steep sides, so signals a little outside the passband are cut hard. A large value means sloping sides that let adjacent-channel signals leak through.
Why not D? Noise factor tells how much noise a stage adds, not how selective it is.